As one of Victoria’s premier steel processers, Eliott Engineering undertakes a wide variety of projects daily. From the simple to downright intricate, very little is unachievable with our vast equipment and experience.
Specialists in Intricate Pressing
✓ TROUGHS ✓ CONES ✓ TRANSITIONS ✓ ANGLES ✓ CHANNELS ✓ SHELLS ✓ ROLL + PRESS COMBINATIONS ✓ WEAR PLATE / HIGH STRENGTH PLATE ✓ UP to 60MM MILD STEEL
Project: Truck Bump Stop
Project: Mould Castings
Project: Precast Concrete Panel Mould
Project: Water Truck Side Body
Project: Sleeper Moulds
Project: Gal Plant Supports
Project: Mining Trough
Project: Side Casting Panels
Project: Light Poles
Project: Bump Stop
Project: All Terrain Vehicles
Project: Agricultural Cutting Implements
Project: Trommel Screen
-
Project: Truck Bump Stop
Project Info:
Material: 20mm mild steel G350
Length: 8000mm long
Highlight: tight radius bends -
Project: Mould Castings
Project Info:
Material: 50mm mild steel G250
Length: various
Highlight: multiple bends across the same plate -
Project: Precast Concrete Panel Mould
Project Info:
Material: 8mm mild steel G250
Length: 7000mm long, 2500mm wide
Highlight: multiple bends across the large piece -
Project: Water Truck Side Body
Project Info:
Material: 6mm mild steel G250
Length: 8000mm long
Highlight: combination of pressing and rolling over a large piece of steel -
Project: Sleeper Moulds
Project Info:
Material: 3mm P&O
Length: 3000mm long
Highlight: tight angular bends -
Project: Gal Plant Supports
Project Info:
Material: 50mm mild steel G250
Length: 6000mm long
Highlight: pressing thick material to a tight radius with accuracy of only a few mm -
Project: Mining Trough
Project Info:
Material: 12mm BIS500
Length: 2000mm long
Highlight: pressing 500 grade high strength material to a tight radius -
Project: Side Casting Panels
Project Info:
Material: 12mm BIS80
Length: 3000mm long
Highlight: pressing high strength material from a large plate size -
Project: Bump Stop
Project Info:
Material: 20mm BIS80
Length: 9000mm long
Highlight: pressing long and high strength material -
Project: Agricultural Cutting Implements
Project Info:
Material: 10mm mild steel g350
Length: various
Highlight: tight accurate pressing -
Project: Trommel Screen
Project Info:
Material: 32mm 450 grade wear plate
Length: 1500mm long
Highlight: multiple pressing for hard thick material to get shape
Specialists in Intricate Rolling
✓ VERTICAL AND HORIZONTAL ROLLING ✓ CONES ✓ TRANSITIONS ✓ CYLINDERS (HALF AND FULL) ✓ BARRELS ✓ SHELLS ✓ ROLL + PRESS COMBINATIONS ✓ STRAKES ✓ ROLLING WITH BEVELS/WELD PREPS
Project: Tank Barrels
Project: Buckets
Project: Grading Buckets
Project: Architectural Rings and Cones
Project: Hopper Transition
Project: Rubber Lining Barrels
Project: Pressure Vessel
Project: Barrels
Project: Cones
Project: Angular Barrels
Project: Large Transition
Project: Hoods for Emulsion Mixer
-
Project: Buckets
Project Info:
Material: 8mm 450 grade high strength steel
Length: 300mm long
Highlight: combination of rolling and pressing high strength material -
Project: Grading Buckets
Project Info:
Material: 16mm 450 grade high strength steel
Length: 3000mm long
Highlight: multiple bends to achieve shape -
Project: Hopper Transition
Project Info:
Material: 8mm mild steel
Length: 2200mm
Highlight: pressing transition from square to round shape and trial assembly -
Project: Rubber Lining Barrels
Project Info:
Material: 8mm mild steel
Length: 3000mm
Highlight: rolling barrels with no flat spots for rubber lining -
Project: Pressure Vessel
Project Info:
Material: 50mm boiler plate
Length: 1800mm
Highlight: vertical rolling of 50mm boiler plate -
Project: Barrels
Project Info:
Material: 6mm mild steel
Length: 2500mm
Highlight: large barrels rolled to an accurate shape -
Project: Cones
Project Info:
Material: 6mm grade 350
Length: various
Highlight: rolling four sections to form large cone -
Project: Angular Barrels
Project Info:
Material: 10mm boiler plate
Length: various
Highlight: rolling angular barrels to a high degree of accuracy -
Project: Large Transition
Project Info:
Material: 32mm boiler plate
Length: various
Highlight: rolling two sections to form large cone from thick boiler plate -
Project: Hoods for Emulsion Mixer
Project Info:
Material: 3mm HA300
Length: various
Highlight: combination of rolling and pressing plate to create hood shape with no flat spots